- CONNECT HEADPHONES TO SERATO DDJ SB HOW TO
- CONNECT HEADPHONES TO SERATO DDJ SB MANUALS
- CONNECT HEADPHONES TO SERATO DDJ SB INSTALL
- CONNECT HEADPHONES TO SERATO DDJ SB UPDATE
- CONNECT HEADPHONES TO SERATO DDJ SB SOFTWARE
Aren't any other USB devices than DDJ-SB connected to your computer? Please turn off Blue Tooth or other wireless connections.ġ1. Does your computer have Blue Tooth or other wireless connection? Please cancel the power saving mode of your computer.ġ0. Please connect your computer to DDJ-SB using the included USB cable.ĩ. (Please ensure the internet access is cut off to secure your computer before closing the virus security software.) Please close all the applications including a screen saver and resident software. Don't you have other applications run background? Please connect DDJ-SB directly to your computer's USB terminal.ħ. This is not a defect but a normal process which is unavoidable. When the Master Tempo is turned on, sound quality sometimes changes depending on tracks you play due to the key control process for keeping the same key. The standard input level/ input impedance of the mic input of DDJ-SB is -52dBu/10kΩ.
CONNECT HEADPHONES TO SERATO DDJ SB MANUALS
If the output level switch or gain adjustment is equipped with the wireless microphone or other devices, please lower the signal level to the mic input of this unit.įor further details, please refer to the instruction manuals of such devices. Is the DDJ-SB unit connected to any device with high output level such as a wireless microphone? Are the input levels of MIC and other connected devices appropriate?
CONNECT HEADPHONES TO SERATO DDJ SB SOFTWARE
Set in the Serato DJ software to the minimum buffer size at which no interrruptions in the sound occur.Ĥ. If interruptions in the sound do occur, change in the to. If no breaks in the sound occur, set in the Serato DJ Intro software to the minimum buffer size at which no interruptions in the sound occur. Launch, change to, and check that no interruptions in the sound occur.ģ. Set in the Serato DJ software to the minimum buffer size at which no interruptions in the sound occur.Ģ. Use the procedure below to set the buffer size to the minimum value at which no interruptions in the sound occur.Ĭheck that no interruptions in the sound occur with the Serato DJ Intro’s default setting (buffer size: 512 samples).ġ. In the same way as at the buffer size setting in the Serato DJ Intro setup, the buffer size can also be set by setting the kernel buffer number in the DDJ_SB ASIO settings utility. The buffer size can be adjusted in the Serato DJ Intro setup. Set the buffer size to the minimum value at which no interruptions in the sound occur. If there are interruptions in the sound, increase the buffer size, but note that this makes the latency longer. The latency (the time from which the DDJ-SB is operated until the sound is output) can be shortened by lowering the buffer size setting. Is the buffer size appropriately adjusted? > No audio output through the master output or headphones.ģ. Read this category first when you see a trouble. ⇒ Check the position of all the knobs and switches of DDJ-SB. Are the knobs and sliders for volume level appropriately adjusted? Is your computer spec above the minimum requirements for the DJ software?Ģ. Depending on your computer, especially for a Build-to-Order PC, an amplifier connected to DDJ-SB and the grounding conditions, the touch sensor of the jogs might not work properly as expected.ġ. If the jog works, the problem could be caused by the devices connected to the unit. If the jog does not work, the unit itself could be the cause of this problem. Touch on a jog with one hand and touch on any part of DDJ-SB other than the jogs with another hand: Please use a soft and dry cloth for cleaning the jog.Ĭlean the stain with the dampened and wrung-out cloth with diluted neutral detergent by 5-6 times of water.ģ) Please conduct the following test to sort out the cause:
CONNECT HEADPHONES TO SERATO DDJ SB UPDATE
Please update the latest firmware to enhance the product's performance.īecause the jog on this unit has a touch sensor, dirt or hand cream on your hand onto the jog would prevent the touch sensor from fully functioning. The firmware is system software program on DDJ-SB device.
Turn the knob to adjust the output sound from the headphone to the appropriate level. Turn the knob to adjust the output sound from the speakers.ģ. Turn the knob to adjust the orange LED of the channel level indicators to light at the peak level.ĥ. Turn the knob to an appropriate position.Ĥ. Please note if the volume is increased too high, an extremely loud sound would be output.ġ.
CONNECT HEADPHONES TO SERATO DDJ SB HOW TO
How to output the sound from CH1 is described below as an example.Įnsure that the volume of the devices (Powered amplifier, powered speaker, etc.) connected to is properly adjusted.
CONNECT HEADPHONES TO SERATO DDJ SB INSTALL
Refer to “Installing the software” on the operating instructions to install the driver software.
Is the driver software already installed on the computer?įor Windows, install the driver software from the included CD-ROM.